NACHI 51126 thrust ball bearings

Grease Speed Rating n1:2400 rpm; Fillet Radius ra:2.00 mm; Accessories:One Seal; D:160.0000 mm; Basic Static Radial Load Rating Co:193000 N; Basic Dynamic Radial Load Rating C:151000 N; d:90.000 mm; Sealed Speed Rating n3:2400 rpm; Oil Speed Rating n2:3400 rpm; B:52.40 mm;

Speed Rating-Single and Double Sealed Grease SDG:5000 rpm; Adapter Sleeve AS:SNW9; Fillet Radius ra:1.00 mm; Basic Radial Load Rating-Dynamic DC:8180 N; Inside Diameter D:36.5125 mm; Basic Radial Load Rating-Static SCO:5130 N; Variant:SZZX Two Seals; B:19.00 mm; D:85.0000 mm;

Basic Static Radial Load Rating Co:16600 N; Basic Dynamic Radial Load Rating C:24200 N; D:47.0000 mm; B:28.00 mm; Grease Speed Rating n1:9500 rpm; Oil Speed Rating n2:14000 rpm; Fillet Radius rb:0.60 mm; Fillet Radius ra:1.00 mm; d:20.000 mm;

d2 ≈:203 mm; D:310 mm; Mass bearing + sleeve:36 kg; D1 ≈:267 mm; b:16.7 mm; da max.:203 mm; Calculation factor Y0:2.5; Calculation factor e:0.27; B:86 mm; d3:220 mm;

B:18.00 mm; D:80.0000 mm; d:40.000 mm; Oil Speed Rating Open/Shielded n2:10000 rpm; Fillet Radius ra:1.00 mm; Basic Dynamic Radial Load Rating C:30700 N; Accessories:Without Accessories; Basic Static Radial Load Rating Co:19000 N; Sealed Speed Rating n3:5600 rpm; Grease Speed Rating n1:8500 rpm;

D:26.0000 mm; d:17.000 mm; Oil Speed Rating Open/Shielded n2:30000 rpm; Sealed Speed Rating n3:16000 rpm; Basic Static Radial Load Rating Co:1460 N; Grease Speed Rating Open/Shielded n1:24000 rpm; B:5.00 mm; Fillet Radius ra:0.30 mm; Basic Dynamic Radial Load Rating C:2250 N; Accessories:Two Seals;

B:80 mm; Reference speed:630 r/min; Limiting speed:800 r/min; d1 ≈:352 mm; b1:9.4 mm; r1,2 min.:2.1 mm; Basic static load rating C0:2280 kN; ra max.:2 mm; Basic dynamic load rating C:897 kN; E:379.7 mm;

l4 max.:349 mm; Basic static load rating C0:530 kN; h1:265 mm; dk:92 mm; C1 max.:43 mm; Specific dynamic load factor K:100 N/mm²; α:6 °; Mass rod end:10.5 kg; l7 min.:78 mm; l3 min.:80 mm;

Mass bearing:713 kg; Basic dynamic load rating C:10800 kN; Design variant/feature:BC4.21/W33GWI; C:486 mm; Basic static load rating C0:27000 kN; D1 ≈:718 mm; Calculation factor kr:0; Fatigue load limit Pu:2120 kN; B:559.5 mm;

Specific static load factor K0:45 N/mm²; d:150 mm; h:152 mm; Permissible sliding velocity v min.:0 m/s; B:100 mm; Tolerance shaft:e7; Mass bushing:4.8 kg; Tolerance housing:H7; D:170 mm; Permissible sliding velocity v max.:0.5 m/s;

D:12 mm; Permissible sliding velocity v min.:0 m/s; Specific dynamic load factor K:25 N/mm²; Tolerance housing:H7; d:7 mm; B:10 mm; Specific static load factor K0:45 N/mm²; Coefficient of friction µ max.:0.15; Mass bushing:0.0066 kg; Permissible sliding velocity v max.:0.5 m/s;

Width - Inner Ring B1:53.98 mm; Speed Rating-Open and Shielded-Grease OSG:4300 rpm; Speed Rating-Open and Shielded-Oil OSO:5300 rpm; D:130.0000 mm; d:60.000 mm; Width - Outer Ring B0:31.0 mm; Basic Radial Load Rating-Dynamic DC:91300 N; Fillet Radius ra:2.00 mm; Basic Radial Load Rating-Static SCO:7

Housing:FSAFS 515; P60°:75.6 kN; A2:195.262 mm; h:28.575 mm; Initial grease fill:68.04 g; Max. speed for Taconite seal:1250 r/min; da:61.913 mm; ba:32.544 mm; N1:15.875 mm; L:285.75 mm;

Da:200 mm; Eye bolt:2 x 3/8-16 UNC; Pa:20.2 kN; Mass pillow block:50.8 kg; Cap bolt recommended tightening torque:298.3 N·m; da:109.537 mm; Taconite seal:TER 115; PG:1/4 NPT; H2:52.388 mm; N1:24.209 mm;

Specific static load factor K0:300 N/mm²; dk:207.162 mm; Sealing solution:-; da max.:178.3 mm; b1:11 mm; Lubricant:Regular relubricatio; r2 min.:1.1 mm; D:222.25 mm; M:8 mm; Design (sliding contact surface combination):Steel/steel;